The automotive industry must ensure that its products operate over this wide temperature range and do not fail or material fatigue under rapid temperature changes.
Therefore, material and component testing, including temperature simulation, is very important and indispensable for the automotive industry, including all suppliers.

On the test benches in the automotive industry, highly dynamic temperature control systems are used for material and component testing, which can achieve precise regulation and rapid temperature changes. Only precise temperature management can provide reliable and repeatable results. The temperature control system provides a constant temperature or a complex temperature curve to the test bench directly or indirectly through a liquid medium. In addition to the temperature of the medium, temperature control systems also allow precise control of flow rates and operating pressures. Temperature control systems are used primarily in two ways: They simulate external ambient conditions in climate chambers or replace internal systems, such as the cooling circuit of an engine. The latter allows realistic conditions to be created on test benches, where test specimens are supplied with coolant according to operational requirements, such as in a vehicle.

Мы поставляем нашим клиентам в автомобильной промышленности высокопроизводительные устройства. Они не только динамически охватывают весь диапазон температур от -40°C до +160°C и быстро меняют температуру на испытательных стендах.

● Efficient production stability and repeatability results;
Использование пластинчатых теплообменников и трубопроводных нагревателей для повышения скорости охлаждения и нагрева;
● Very wide temperature range, no need to replace liquid medium;
Полностью закрытая система, продлевающая срок службы теплопроводных жидкостей;
● Adopting magnetic drive pump, there is no problem of shaft seal leakage

Can meet the direct cooling/direct heating for battery pack and vehicle testing and testing. This equipment is mainly used for cooling and heating capacity testing. It uses variable frequency compressor with adjustable output;

The testing unit needs to use specific temperature change curves and record temperature changes; The temperature range is usually -40 ℃ to 100 ℃ (can expand to 150 ℃); When conducting tolerance testing, it is usually done in an infinite cycle.

Suitable for more simulation test temperature control
Equipment application: new energy battery pack, battery module, battery cell, motor and controller, charger, DC/DC converter, electronic pump

Low Temp/Normal Temp Chillers (Biochemistry Pharmaceutical Process)

Temperature Control :-5℃~-150℃

Регулирование температуры для различных реакторов, систем дистилляции или экстракции, лабораторий, научно-исследовательских институтов, химической, фармацевтической, нефтехимической, биохимической, медицинской промышленности, больниц, научно-исследовательских и опытно-конструкторских мастерских, испытаний полупроводников, аэрокосмической промышленности, биологии.

Системы динамического контроля температуры (Biochemistry Pharmaceutical Process)

Temperature Control :-120℃~350℃

Temperature control for high pressure reactor；Double-layer glass reactor；Double-layer reactor；Microchannel Reactor；Distillation system；Material aging test；Vacuum chamber etc.

Control Temperature Control Flow Systems（Vehicle/Battery Pack Test)

Temperature Control: -40℃~100℃

Моделирование температуры для проверки качества автомобиля: проверка срока службы аккумулятора, стенд для проверки топливных форсунок/двигателей, проверка подушек безопасности, стенд для проверки компонентов и т.д. Он может имитировать внешние условия окружающей среды в климатической камере или заменить внутреннюю систему, которая может создать необходимые фактические температурные условия для испытательного стенда.

Cooling Heating Systems (Semiconductor Production）

Temperature Control: -85℃~250℃

Suitable for semiconductor process wet washing, photolithography, etching, chemical meteorological deposition, physical meteorological deposition, and the electronics industry (photolithography process)